User Tools

Site Tools


base:code_frame_for_16_kb_crt-images

Raw Frame for Generic 16 KB cart images

; raw frame for generic 16 KB cartridge images
; v 1.0 enthusi 04/2012
; this 16 KB Cartridge framework was written for http://www.rgcd.co.uk
; feel free to use/change this code and give credits :)
; you will find this document also at http://codebase64.org
; this is a VERY simple but efficient approach, you can make more 
; sophisticated usage of ROM using an own depacker routine etc....
; sources are in XA format but no special features are used
; I strongly recommend the usage of cartconv which comes with vice
; you can as well set up your own crt-header, which will look 
; more or less like this:
;.asc "C64 CARTRIDGE   "
;.byte $00,$00   ;header length
;.byte $00,$40   ;header length
;.word $0001     ;version
;.word $0000     ;crt type
;.byte $00       ;extrom line
;.byte $00       ;game line
;.byte $00,$00,$00,$00,$00,$00 ;unused
;.asc "MY NAME"
;name
;.dsb ($0040-name),0
;;chip packets
;.asc "CHIP"
;.byte $00,$00,$40,$10   ;chip length?
;.byte $00,$00   ;chip type
;.byte $00,$00   ;bank
;.byte $80,$00   ;adress
;.byte $40,$00 ;length
;ROM part follows...

The following is for creating a .bin file of 16384 Bytes length as you would burn it onto EPROM, or to use as input for cartconv and alike.

;---------------------------------------------------------- 
; example usage
; xa frame.asm -o frame.bin
; cartconv -t normal -i frame.bin -n 'my cart' -o frame.crt
; x64 -cartcrt frame.crt
;----------------------------------------------------------

;no load-adress for bin-file, so no header here

*=$8000
.word launcher ;cold start
.word launcher ;warm start
.byte $c3	;c
.byte $c2	;b
.byte $cd	;m
.byte $38	;8
.byte $30	;0

launcher
  stx $d016
  jsr $fda3	;prepare irq
  jsr $fd50	;init memory
  jsr $fd15	;init i/o
  jsr $ff5b	;init video
                ;make sure this sets up everything you need,
                ;the calls above are probably sufficient
  ldx #$fb
  txs

;set up starting code outside of cartridge-area
move_starter
  ldx #(starter_end-starter_start)
loop1
  lda starter_start,x
  sta $100,x
  dex
  bpl loop1
  jmp $100
;---------------------------------
starter_start	
  ldx #$40 ;64 pages = 256 * 64 = 16384 Bytes
  ldy #0
loop
src
  lda exomized_data,y
dst
  sta $801,y
  iny
  bne loop
  inc src+2-starter_start+$100 
  inc dst+2-starter_start+$100
  dex
  bpl loop

;make sure settings for $01 and IRQ etc are correct for your code
;remember THIS table from AAY64:

;       Bit+-------------+-----------+------------+
;       210| $8000-$BFFF |$D000-$DFFF|$E000-$FFFF |
;  +---+---+-------------+-----------+------------+
;  | 7 |111| Cart.+Basic |    I/O    | Kernal ROM |
;  +---+---+-------------+-----------+------------+
;  | 6 |110|     RAM     |    I/O    | Kernal ROM |
;  +---+---+-------------+-----------+------------+
;  | 5 |101|     RAM     |    I/O    |    RAM     |
;  +---+---+-------------+-----------+------------+
;  | 4 |100|     RAM     |    RAM    |    RAM     |
;  +---+---+-------------+-----------+------------+
;  | 3 |011| Cart.+Basic | Char. ROM | Kernal ROM |
;  +---+---+-------------+-----------+------------+
;  | 2 |010|     RAM     | Char. ROM | Kernal ROM |
;  +---+---+-------------+-----------+------------+
;  | 1 |001|     RAM     | Char. ROM |    RAM     |
;  +---+---+-------------+-----------+------------+
;  | 0 |000|     RAM     |    RAM    |    RAM     |
;  +---+---+-------------+-----------+------------+

  lda #$35 ;cart is always on instead of BASIC unless it can be switched off via software
  sta $01
  jmp $80d ;for exomizer, i.e.

starter_end
;----------------------------------
exomized_data
.bin 2,0,"data.exo"
;syntax for exomizer 2.0.1:
;exomizer sfx sys game.prg -o data.exo
main_file_end
;fill up full $4000 bytes for bin file ($c000-$8000=$4000)
.dsb ($c000-main_file_end),0
base/code_frame_for_16_kb_crt-images.txt · Last modified: 2015-04-17 04:30 by 127.0.0.1