This is an old revision of the document!
Hi, I'm Hermit Soft. On CSDB I've shared my strongly optimized (shortened) CIA-timer using stable raster method. Now it's here to fill the gap in Codebase64. I hope it will be useful in “everyday's demo coding” . :)
A short pre-description: The first cmp$d012, bne*-3 waits till the raster-row given in the Accu. The occurence of this testing jitters in 1…7 cycles to the real starting (cycle 1) time of the rasterline, because these two commands take 4+3 cycles, and so delays detection. A raster row is 63 cycles long, and CPU can use all these cycles to do operations if no SPRITE or BADLINE fetches the actual raster-row. Also important to prevent memory page-boundaries because some commands take 1 more cycle when crossing them. Use program-start address and scan-part addresses of 256 multiplies to be clear.
We do a second rasterrow-test (cmp $d012) after exactly 56 cycles. This 56 cycles builds up from the carefully programmed part between the first “bne” and the second “cmp $d012”. If the raster-row changed, jitter made too much delay and new row started. In this case we jump back with second “bne” to the syncronization (first cmp$d012) and repeat this until we catch a case when the jitter doesn't make delay, and we can set our timer to it.
The timer (re)starts with sta$dc0e,y which is the most strictly timed, to show 7…1 on $dc04 when using the d012 scan (B-part). It counts 9 steps like 8,8,7,6,5,4,3,2,1….and again and again. It runs in cycle-syncron with the raster-beam.
Accumulator can be any value, no need to set.
sei ;we don't want lost cycles by IRQ calls :) sync: cmp $d012 ;scan for begin rasterline (A=$11 after first return) bne *-3 ;wait if not reached rasterline #$11 yet ldy #8 ;the walue for cia timer fetch & for y-delay loop 2 cycles sty $dc04 ;CIA Timer will count from 8,8 down to 7,6,5,4,3,2,1 4 cycles dey ;Y=Y-1 (8 iterations: 7,6,5,4,3,2,1,0) 2 cycles*8 bne *-1 ;loop needed to complete the poll-delay with 39 cycles 3 cycles*7+2 cycles*1 sty $dc05 ;no need Hi-byte for timer at all (or it will mess up) 4 cycles sta $dc0e,y ;forced restart of the timer to value 8 (set in dc04) 5 cycles lda #$11 ;value for d012 scan and for timerstart in dc0e 2 cycles cmp $d012 ;check if line ended (new line) or not (same line) sty $d015 ;switch off sprites, they eat cycles when fetched bne sync ;if line changed after 63 cycles, resyncronize it! .... ;the rest (this is also a stable-timed point, can be used for sg.)
scan: ldx #$31 ;a good value that's not badline, in border and 1=white cpx $d012 ;scan rasterline bne *-3 ;wait until rasterline will be $31 lda $dc04 ;check timer A, here it jitters between 7...1 eor #7 ;A=7-A so jitter will be 0...6 in A sta *+4 ;self-writing code, the bpl jump-address = A bpl *+2 ;the jump to timer (A) dependent byte cmp #$c9 ;if A=0, cmp#$c9; if A=1, cmp #$c9 again 2 cycles later cmp #$c9 ;if A=2, cmp#$c9, if A=3, CMP #$EA 2 cycles later bit $ea24 ;if A=4,bit$ea24; if A=5, bit $ea, if A=6, only NOP ........... anything you like, let's see a short example stx $d020 ;x was 1 so border is white at the stable cycle sty $d020 ;y ended in 0 in sync routine, so border black after 4 cycles ........... ;pay attention on delay before rescan rasterline, to avoid cmp$D012 again on this same rasterline in the middle. If the scan happens again in the same line, that may crash the program, because DC04 won't be usable for jumptable. (For this stx $d020, sty$d020 this is specially not problem because of the lucky timing. They're for try the routine.) jmp scan ;go to the raster again (or can go new raster)
The first part (CIA setter) is also good for raster IRQ. The important thing is to do the “pha” (3 cycles) before “lda $dc04” in the called irq.
irq: pha lda $dc04 eor #7 sta *+4 bpl *+2 lda #$a9 lda #$a9 lda $eaa5 txa pha tya pha ; the rest processes in the IRQ routine asl $d019 pla tay pla tax pla rti
That's for now, test it, use it, or whatever you want… Or you can ask questions on csdb forum for this topic: